<_x0034_00701957>

400701957 06 47120 KERR MCGEE OIL & GAS ONSHORE LP

P O BOX 173779

DENVER CO 80217-3779 REBECCA HEIM 720 929-6361 720 929-7361 CHERYL LIGHT SR. REGULATORY ANALYST 2014-10-06T11:10:16.547-06:00 DRAFT heimr 2014-10-06T11:10:16.547-06:00 heimr DJRegulatory@anadarko.com 0.00000 REBECCA.HEIM@ANADARKO.COM heimr heimr 2014-10-06T11:18:13.11-06:00 400701957 Carlile, Craig 970 629-8279 05 123 14454 00 UPRR 22 PAN AM UT/ V 1 NWNE 19 3N 65W 6 WELD WATTENBERG 90750 N PRODUCTION Y 1290 N � N 40.215230 -104.702540 2006-06-13T00:00:00-06:00 Chris Fisher 1.9 PLUG AND ABANDON PROCEDURE (SEE ATTACHED PROCEDURE) 1. Provide 48 hr notice to COGCC prior to rig up per request on approved Form 6 (e.g. call field coordinator, submit Form 42, etc.). Call IOC (970-506-5980) at least 24 hr prior to rig move. Request they catch and remove plunger, isolate production equipment and remove any automation prior to rig MIRU. 2. MIRU slickline services. Pull bumper spring and tag bottom. 3. PU pressure bomb and obtain pressure gradient survey from halfway between the bottom and top perfs to surface (+/- 7,800’ to surface). Forward pressure bomb results to Evans Engineering. POOH and LD the pressure bomb. 4. MIRU VES. PU Gyro and run from tbg SN (+/- 7,772) to surface. POOH and LD Gyro. RDMO VES & slickline services. 5. Prepare location for base beam equipped rig. Install perimeter fence as needed. 6. Check and record Bradenhead pressure. If Bradenhead valve is not accessible, re-plumb so that valve is above GL. 7. MIRU WO rig. Kill well as necessary w/ water containing biocide. ND WH, NU BOP. 8. Unseat and LD landing joint. PU w/ 2-3/8” tbg (4.7#, J-55, 8rd EUE) to break any sand bridges. Do not exceed the safety tensile load of 57,384 lbs (80% of upset yield strength). 9. TOOH and SB 2-3/8” tbg (266 jts landed at 7,772’). 10. PU scraper for 5-1/2”, 17# csg on 2-3/8” tbg. TIH to +/- 7,750’ (+/- 250 jts). TOOH and SB tbg. 11. MIRU Wireline. PU CIBP for 5-1/2” 17# csg on wireline and RIH to 7,740’. Set CIBP in the csg at 7,740’. Pressure test to 1000 psi for 15 min. RDMO Wireline. 12. TIH 2-3/8” tbg and tag the CIBP at +/- 7,740’ while hydrotesting each joint to +/- 3000 psi and tag CIBP. Pick up 5’ from tag. 13. MIRU Cementing Services. Spot 110 sx (+/- 152 cuft) of cmt (Class G w/ 20% silica flour, 0.4% CD-32, 0.4% ASA-301, and R-3 to achieve 2:30 pump time) mixed at 15.8 ppg and 1.38 cuft/sk from 7,740’ to 6,650’. RDMO Cementing Services. 14. PUH w/ 2-3/8” tbg to +/- 6,000’ (+/- 56 jts) and circulate tbg clean. POOH, SB +/- 3,810’ of tbg, LD remainder. 15. MIRU Wireline. PU and RIH on wireline two 1’ perf guns (3-1/8”, 3 spf, “Big Hole” 0.6” EHD, 7” penetration, 120o phasing, 2’ net, 6 total holes) to 4,180’. Perf bottom squeeze holes at 4,180’ then PUH to 3,780’ and perf top squeeze holes in 5-1/2” prod csg. POOH perf guns. RDMO wireline. 16. PU CICR for 5-1/2” 17# csg on 2-3/8” tbg. TIH and set at +/- 3,810’ (+/- 123 jts). 17. MIRU Cementing Services. Pump 5 bbls of fresh water, 20 bbls of metalillicate, and 5 bbls of craig.carlile@state.co.us false 400701957 400701957 FORM 6 INTENT SUBMITTED 400701957.pdf 400701957 400701966 PROPOSED PLUGGING PROCEDURE UPRR 22 PAN AM V #1 PROCEDURE.pdf 62834 400701957 400701967 WELLBORE DIAGRAM UPRR 22 PAN AM V #1 WBD.pdf 72554 400701957 JSND 7792 7861 400701957 0 110 7740 false 400701957 1 25 80 false 400701957 2 CASING 110 6650 7740 false 400701957 3 false 400701957 4 false 400701957 5 false 400701957 6 false 400701957 7 270 4180 false 3810 400701957 8 false 400701957 9 false 400701957 10 420 520 1390 false 400701957 11 25 false 400701957 12 false 400701957 13 false 400701957 14 false 400701957 15 false 400701957 16 false 400701957 1ST 7 7 8 5 1 2 17 7987 350 7987 6607 CBL ACTUAL 400701957 SURF 12 1 4 8 5 8 24 721 430 721 0 VISU ACTUAL Thread was being aborted.