<_x0034_00701897>

400701897 06 47120 KERR MCGEE OIL & GAS ONSHORE LP

P O BOX 173779

DENVER CO 80217-3779 REBECCA HEIM 720 929-6361 720 929-7361 CHERYL LIGHT SR. REGULATORY ANALYST 2014-10-06T10:26:25.64-06:00 DRAFT heimr 2014-10-06T10:26:25.64-06:00 heimr DJRegulatory@anadarko.com 0.00000 REBECCA.HEIM@ANADARKO.COM heimr heimr 2014-10-06T10:35:15.22-06:00 400701897 Carlile, Craig 970 629-8279 05 123 14633 00 HSR-M CHRISTINE 2-22 NWNE 22 3N 66W 6 WELD WATTENBERG 90750 N PRODUCTION Y 1190 N N N 40.215980 -104.760480 2006-01-10T00:00:00-07:00 Steve Fisher 2.7 M Christine 2-22 (SEE ATTACHED PROCEDURE) PLUG AND ABANDON PROCEDURE 1. Provide 48 hr notice to COGCC prior to rig up per request on approved Form 6 (e.g. call field coordinator, submit Form 42, etc.). Call IOC (970-506-5980) at least 24 hr prior to rig move. Request they catch and remove plunger, isolate production equipment and remove any automation prior to rig MIRU. 2. MIRU slickline services. Pull bumper spring and tag bottom. RDMO slickline services. 3. Prepare location for base beam equipped rig. Install perimeter fence as needed. 4. Check and record Bradenhead pressure. If Bradenhead valve is not accessible, re-plumb so that valve is above GL. 5. MIRU WO rig. Kill well as necessary w/ water containing biocide. ND WH, NU BOP. 6. PU the 2-3/8” tbg (4.7#, J-55, 8rd EUE) to break any sand bridges. Release the Arrow-Set packer (at 6,400’). Do not exceed the safety tensile load of 57,384 lbs (80% of upset yield strength). 7. TOOH. SB +/- 7,050’ of tbg, LD the remainder. 8. PU scraper on 2-3/8” tbg and TIH to +/- 7,040’. TOOH, SB tbg, and LD the scraper. 9. MIRU Wireline. PU CIBP for 4.5” csg (11.6#, M-75, LTC). RIH and set CIBP at 7,030’ (Note: Collars are at 7,004’, 7,048’, & 7,092’). POOH and LD the setting tool. Pressure test CIBP to 1000 psi for 15 min. RDMO Wireline. 10. TIH 2-3/8” tbg and tag the CIBP (at +/- 7,030’) while hydrotesting each stand to +/- 3000 psi. 11. MIRU Cementing Services. Spot 30 sx (+/- 41 cuft) of cmt (Class G w/ 20% silica flour, 0.4% CD-32, 0.4% ASA-301, and R-3 to achieve 2:30 pump time) mixed at 15.8 ppg and 1.38 cuft/sk from 7,030’ to 6,700’ on top of CIBP. 12. PUH w/ 2-3/8” tbg to +/- 6,000’ (+/- 22 jts) and circulate tbg clean. POOH, SB +/- 4,180’ of tbg, LD remainder. 13. MIRU Wireline. PU and RIH two 1’ perf guns (3-1/8”, 3 spf, “Big Hole” 0.6” EHD, 7” penetration, 120o phasing, 2’ net, 6 total holes) to 4,560’. Perf bottom squeeze holes at 4,560’ then PUH to 4,150’ and perf top squeeze holes in 4-1/2” prod csg. POOH and LD perf guns. RDMO wireline. 14. PU CICR for 4-1/2” csg (11.6#, M-75, I-70) on 2-3/8” tbg and set at +/- 4,180’. 15. MIRU Cementing Services. Pump 5 bbls of fresh water, 20 bbls of metalillicate, and 5 bbls of fresh water followed with 180 sx (+/- 207 cuft) of cmt (Class G w/ 0.25 pps cello flake, 0.4% CD-32, 0.4% ASA-301) mixed at 15.8 ppg and 1.15 cuft/sk. Under displace by 3bbls of cement, sting out of CICR and dump cmt on CICR. Planned cement is from 4,560’ to 4,150’ in 9” OH (plus 20% excess) & from 4,560’ to 4,050’ in 4-1/2”, 11.6# csg. PUH to +/- 3,350 (+/- 22 jts) and circulate to clean tbg. TOOH and SB +/- 1,300’ of tbg and LD remainder. RDMO Cementing Services. 16. MIRU wireline. PU a jet cutter and RIH to +/- 1,190’ to cut 4-1/2” csg. Cut csg and circulate bottoms up. Continue to circulate to remove any gas from the wellbore. RDMO wireline. 17. ND BOP and tbg head. NU BOP of the surface csg head w/ 4-1/2” pipe rams. Install 3,000 psi rated ball valves on both surface csg outlets. Install a choke or a choke manifold on one of the outlets. 18. TOOH and LD 4-1/2” csg. 19. Remove the 4-1/2” pipe rams and install 2-3/8” pipe rams on the BOP. 20. TIH w/ 2-3/8” tbg to +/- 1,290’. Page 2 of 2 21. MIRU Cementing Services. Pump 10 bbls of SAPP (Sodium Acid Pyrophosphate) followed by 20 bbls of fresh water containing biocide. Spot 370 sx (+/- 492 cuft) of cmt (Type III w/ cello flake and CaCl2 as deemed necessary) mixed at 14.8 ppg at 1.33 cuft/sk. Planned cement is from 1,290’ to 1,190’ stub plug in 4-1/2”, 11.6# csg stub, 1,190’ to 615’ in 9” OH (plus 60% excess), and from 615’ to 410’ inside 8-5/8”, 24# surface csg. PUH to 250’ and circulate tbg clean. RDMO Cementing Services. WOC for 4 hrs. 22. TIH w/ 2-3/8” tbg and tag TOC and if TOC is deeper than 410’ contact engineer for possible further cement work. TOOH and LD 2-3/8” tbg. 23. MIRU wireline. PU CIBP on wireline for 8-5/8” (24#) csg and TIH to +/- 80’. Set CIBP and test to 1000 psi for 15 min. POOH and LD wireline craig.carlile@state.co.us false 400701897 400701897 FORM 6 INTENT SUBMITTED 400701897.pdf 400701897 400701905 PROPOSED PLUGGING PROCEDURE M CHRISTINE 2-22 (HSR) PROCEDURE.pdf 60691 400701897 400701911 WELLBORE DIAGRAM M CHRISTINE 2-22 (HSR) WBD.pdf 73346 400701897 CODL 7306 7347 400701897 NBRR 7109 7174 400701897 0 30 7030 false 400701897 1 25 80 false 400701897 2 false 400701897 3 false 400701897 4 false 400701897 5 false 400701897 6 false 400701897 7 180 4560 false 4150 400701897 8 false 400701897 9 false 400701897 10 370 410 1290 false 400701897 11 25 false 400701897 12 false 400701897 13 false 400701897 14 false 400701897 15 false 400701897 16 false 400701897 1ST 7 7 8 4 1 2 11.6 7473 180 7473 6386 CBL ACTUAL 400701897 SURF 12 1 4 8 5 8 24 615 400 615 0 VISU ACTUAL Thread was being aborted.